Men 3XL (chest 116 cm)

Button-up shirt pattern, men's size 3XL (116 cm chest)

Classic button-up shirt with collar and cuffs, highly customizable. Sized without bust.

Button-up shirt – Men 3XL (chest 116 cm)
Full pattern with 1 cm seam allowance · 172 × 103 cm
12pattern pieces
27pieces to cut
≈ 2.5 ydof main fabric (60" wide)

You will also need: interfacing.

Sewing instructions

General steps to sew this garment. Seam allowance is 1 cm (3/8") unless stated otherwise.

Supplies

  • Shirting (poplin, oxford, linen)
  • Fusible interfacing
  • Buttons
  • Matching thread and the right needle
  1. Prewash and press your fabric before cutting so it will not shrink after sewing.
  2. Print the pattern at 100%, check the test square and cut the pieces following the cutting list. Transfer notches, darts and button marks.
  3. Press and sew the button and buttonhole plackets on the fronts.
  4. Attach the yoke with the "burrito" method: back between the two yoke layers, then the front shoulders.
  5. Interface the collar and stand. Sew the collar, turn, topstitch and sandwich it between the stand layers; attach the stand to the neckline.
  6. Slash the sleeve vent and sew the sleeve placket (overlap and underlap pieces).
  7. Set the sleeves flat with a flat-felled or serged seam.
  8. Sew the underarm and side seam in one go, matching the armhole seams.
  9. Interface the cuffs, sew, turn and attach them to the sleeves, matching the pleats.
  10. Hem: double-fold to the inside, press and topstitch or blind stitch.
  11. Mark and sew the buttonholes, then sew on the buttons opposite them.

Cutting list

PieceCutMaterial
Back1× on the foldMain fabric
Buttonhole placket1×Main fabric
Button placket1×Main fabric
Collar and undercollar1×Main fabric
Collar and undercollar1×Main fabric
Collar and undercollar1×Interfacing
Collar and undercollar1×Interfacing
Collar stand2×Main fabric
Collar stand2×Interfacing
Cuff4×Main fabric
Cuff2×Interfacing
Front right1×Main fabric
Front left1×Main fabric
Sleeve2×Main fabric
Sleeve placket overlap2×Main fabric
Sleeve placket underlap2×Main fabric
Yoke2×Main fabric

Measurements used in this size

MeasurementValueHow to measure
Biceps circumference40.5 cmAround the widest part of the relaxed upper arm.
Chest/bust circumference115.8 cmAround the torso at the fullest part of the chest, tape level.
Shoulder to bust30.9 cmFrom the high point of the shoulder (next to the neck) to the bust point.
Back length51.8 cmFrom the high shoulder point, down the back, to the waist.
Neck circumference44 cmAround the base of the neck, where a shirt collar sits.
Shoulder width49.6 cmFrom one shoulder point to the other, across the back.
Shoulder slope13°Shoulder angle in degrees (usually between 10 and 15).
Waist to armpit23.2 cmVertically along the side, from the waist to the armpit.
Waist to hips14.3 cmAlong the side, from the waist to the hip line.
Waist circumference91.9 cmAround your natural waist, the narrowest part of the torso.
Hip circumference97.3 cmAround the hips, at the level of the hip bones.
Arm length66 cmFrom the shoulder point to the wrist, arm slightly bent.
Wrist circumference18.9 cmAround the wrist, over the bone.

Between two sizes?

Standard sizes are a starting point. Enter your own measurements in the editor and the pattern is redrafted for your body in seconds, for free.

Open in the editor